Jump to content

Recommended Posts

Posted

Getting to my 3788 project. No lube pressure or MCV pressure. Steering works just fine brakes work and clutch assist works. What gives?

Main hydraulic circuit and 3 point work just fine. Changed filters already. Fluid is moving in the rear end. Should there be more?

IMG_3652.jpeg

Posted

Im no expert but sounds like a problem in the MCV. Get a set of gauges and verify you in fact don't have lube and no pressure to TA. If you find no pressure, TA rebuild with spring kit is cheap from Ag Parts. Make sure you replace jumper tube o-rings to the TA as well.

Posted

Pull the MCV valve off and check the gasket behind the steel block that’s bolted on where the MCV pump would go on other tractors with the the pump .

DannyĀ 

  • Like 1
Posted
10 hours ago, CJSuhr said:

Im no expert but sounds like a problem in the MCV. Get a set of gauges and verify you in fact don't have lube and no pressure to TA. If you find no pressure, TA rebuild with spring kit is cheap from Ag Parts. Make sure you replace jumper tube o-rings to the TA as well.

0 lube and like 30-40 psi on TA circuit which is about as good as zero lol

Posted
1 minute ago, snoshoe said:

The gasket Danny mentioned was my first thought. Clutch booster and brakes working made me say dump valve.

This should have the spring kit with it? Been awhile since I did my 1566.

IMG_3661.png

Posted
4 minutes ago, 1566IH said:

This should have the spring kit with it? Been awhile since I did my 1566.

IMG_3661.png

Being the odd man on here. We did not use hy-capacity. My only experience with spring kits was cutting the springs to get the pressure back down to quit blowing gaskets. To answer your question. It does not appear spring kit is part of that package.

Posted

My fix for the blown gasket on that block was to machine a square recess to hold an oring that went around both ports. The block just connects the two ports so one oring does it and no gasket to blow.

  • Like 1
Posted
49 minutes ago, 1566IH said:

Thats what im questioning its the same part number as ag parts MCV gasket and spring kit.

Did some googling and I see your dilemma. Part number is borrowed minus the suffix. Image apparently is too. Several sites use it. Some descriptions say springs are included. Others don't say. Think I would call before ordering.Ā 

Posted
1 hour ago, snoshoe said:

Did some googling and I see your dilemma. Part number is borrowed minus the suffix. Image apparently is too. Several sites use it. Some descriptions say springs are included. Others don't say. Think I would call before ordering.Ā 

Got it figured out. Called and it took a bit but found it

IMG_3662.png

  • Like 1
Posted
47 minutes ago, IHC_1470 said:

It has been years ago now but my 37 was doing about the same thing. It actually ended up being a bad TA.

Thats what Im working on process of elimination. Obviously TA wont work with to pressure to start with. This will be the last thing.

Ā 

Also is there anything you can do to block off the TA circuit to eliminate that as a possibility or is there lube needed for that circuit?

Posted
16 minutes ago, 1566IH said:

Thats what Im working on process of elimination. Obviously TA wont work with to pressure to start with. This will be the last thing.

Ā 

Also is there anything you can do to block off the TA circuit to eliminate that as a possibility or is there lube needed for that circuit?

Back off the mcv then slip a piece of shim stock down to cover the ends of the three tubes and tighten back up

Posted
17 minutes ago, snoshoe said:

Back off the mcv then slip a piece of shim stock down to cover the ends of the three tubes and tighten back up

Ok, during normal operation do you need lube pressure in that circuit or is it just for testing purposes?

Posted

Says in the instructions this will still give lube oil to the TA so I assume the whole circuit can’t be blocked off.

IMG_3663.jpeg

Posted

Just need to block the Hi and Lo jumper tubes -- leave the lube tube openĀ 

I just tapped out two jumpers and put 1/8" plugs in the holeĀ 

But really only need to block one jumper off -- the control valve only lets oil in the jumper that you have selected with the handleĀ 

Most of the time one can use air on a jumper to test the clutch packs and seal rings good enough
-- hear air -- then there is a leakĀ 

That closed center system -- will be the block gasket on the backside of the mcv -- or a gasket inside is the usual causeĀ 

Posted
5 minutes ago, HydroTek said:

Just need to block the Hi and Lo jumper tubes -- leave the lube tube openĀ 

I just tapped out two jumpers and put 1/8" plugs in the holeĀ 

But really only need to block one jumper off -- the control valve only lets oil in the jumper that you have selected with the handleĀ 

Most of the time one can use air on a jumper to test the clutch packs and seal rings good enough
-- hear air -- then there is a leakĀ 

That closed center system -- will be the block gasket on the backside of the mcv -- or a gasket inside is the usual causeĀ 

Ok makes sense I dont have my book in front of me of what all the passages are. Obviously the TA isnt functioning as it is. Any harm in running it with the TA "shut off" while leaving the lube circuit open? Running out of time with it before I want to use it and TA replacement is not in the schedule before then if the MCV block reseal and spring job doesn't fix it.

Posted

Just scanned back thru this real quick -- so may miss some stuff

Oil level in that pic is way low -- oil should be at mid point on the axlesĀ 
-- check the dipstick stop collar -- those liked to slip upward and make the stick read wrong

Brakes and assist cylinder use the same oil pressure as the TA clutches -- I find it odd that you say those work but the TA does not shift
-- still will pull in Lo even if there were no oil in the transmission at allĀ 

Have you checked to see that the dump valve is returning back to the inward position ?
-- spring loaded -- just reach and flip it a couple of timesĀ 

if the gasket on the back of the mcv was blown -- would think that brakes and clutch would be weakĀ 

Posted

Yes Ive been fiddling around with the hydraulics so some has been lost. Know I will need to add some.

Thats what also puzzled me is that there is basically no pressure but everything still works fine. Steering brakes and clutch assist. Also there is lube coming out the rear end but no pressure. When I was working on it took out the plug below the lube circuit sensor and it shot oil about 10 feet.

Ā 

Ill work on it tonight with the dump valve and see what happens.

Ā 

Also, like I mentioned before. If I block out the TA pressure and leave the lube circuit open. Will I damage anything running it that way?

Posted
17 minutes ago, 1566IH said:

Also, like I mentioned before. If I block out the TA pressure and leave the lube circuit open. Will I damage anything running it that way?

Shouldn't but that's assuming it restores lube pressure. I think that is unlikely as I don't ever remember losing both dd and ta pressures at the same time through the unit. The dump valve is the only unit I know that will dump dd and ta pressures along with lube and maintain pressure toĀ  clutch and brakes

Posted
3 hours ago, 1566IH said:

When I was working on it took out the plug below the lube circuit sensor and it shot oil about 10 feet.

Yeah , that plug will shoot out a lot of oil , since that is the steering orificeĀ 

Take the lube switch out and put in a gauge (5 to 7 psi is where the light comes on) -- that switch is prone to fail -- check for oil around the wire terminal -- if there is oil the diaphragm is leakingĀ 

Lube you see in the top link cover is oil cooler return -- the ta lube is the same circuit but thru an orifice (drilled passage)

I am not sure on a closed center how the oil is limited from the pump for lube
on a open center lube is the return from steering -- after the TA is done with it (just like closed center systems) -- combined with the excess that the pump is pushing past the flow dividerĀ 

Posted
35 minutes ago, HydroTek said:

Yeah , that plug will shoot out a lot of oil , since that is the steering orificeĀ 

Take the lube switch out and put in a gauge (5 to 7 psi is where the light comes on) -- that switch is prone to fail -- check for oil around the wire terminal -- if there is oil the diaphragm is leakingĀ 

Lube you see in the top link cover is oil cooler return -- the ta lube is the same circuit but thru an orifice (drilled passage)

I am not sure on a closed center how the oil is limited from the pump for lube
on a open center lube is the return from steering -- after the TA is done with it (just like closed center systems) -- combined with the excess that the pump is pushing past the flow dividerĀ 

The axial piston steering pump is regulated to a constant 12 gpm for steering. The return from that is plumbed into what was the supercharge port. Through that steel block into the mcv. Flow divider pulls off 5 gpm for regulated circuit like normal.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...