Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by patricksjohndeeres

  1. I was wondering if anyone would have a spare 7588 or 7788 IHC resin toy tractor 1/16th ... you can email my self at mosset2cylinders@hotmail.com.... thanks
  2. Found two more 1206 Wheatland models in Manitoba, ser number 8567 and 8825 both are running tractors,, these belong to another fellow
  3. I have a 1468 IHC ser #2650118U007408X....... it has been sold going to New Zealand now .. Thanks
  4. How many of these IHC 1468s with a V8 were made ?
  5. anyone making the dust shields for the wheatland IHC tractors ? and what about the step down plates on each side of seat from floor boards to rear step ? used ones would be ok as well
  6. yes need a new fitting for sure, not sure were to get it but will check it out. thanks guys
  7. took the fitting off and it was blocked , I think the ball in fitting that I drilled threw had turned and closed it off again. I used a piece of wire to put threw it again and put it back together, runs good now,, so I will run it for a while and see it it will do it again ,I will have to drill a bigger hole if it happens again , Thanks for the help
  8. that is correct steel fitting on top of pump cover ..I took the return injector line off today as well and blew threw it with air, no blockage there . No blockage to the tank as I blew that out first .
  9. I blew the return line out to the tank nothing in it. I never tried to run it with the line off , I drilled out the bottom little part of the fitting and put it back together and tried it ..
  10. Have a 1256 and it had been sitting for some time, it starts right up and I haver used it around yard a few times, no issues,, yesterday went to use it and started nice ran for about 10 min then powered down and stopped, tried to start again fired up but again powered down. I read the posts that is maybe be return top fuel fitting the issue, I cleaned it and drilled it out and still the same issue... If I loosen the side screws on the small flat plate fuel will spray out and the engine will stay running. the min i turn them tight she stops running.. What could be the issue ? Thanks for any he
  11. located 1206 Wheatland tractors ser 8764 and ser 8958.... they are not mine ....Not sure if you had them listed ...thanks
  12. We did one today with the big wide wheatland fenders with rear entry and also added the front step on left side ,
  13. Have two 1206 IHC Wheatlands , ser 8177 and 8141 ser .. will be converted to open station models
  14. Couple more 1206s Wheatland model user number 8177 which I have now and I know of ser 8141 is
  15. update ser 8857 Wheatland 1206 has been located in alberta Canada 

    1. red_reaper


      Thank you, I did not have it, next in line 8858 was in the Schrock in Indiana and sold at his auction back in 2011, thank you!

    2. redturbo
  16. Update on 806 IHC now,, Its home here now and removed cab and loader, its had a engine over hauled at some time and new engine block as its yellow , nice running tractor ..
  17. just a update, the tractor has a loader on it and the hydraulic lever was in lock position to supply oil to the loader controls, I put it into neutral and now have more oil going to the hydro, I now can get 13 mph out of it in high range ,
  18. does anyone have ph number for them ?
  19. I stand on the brakes when driving and does not make the trans slip at all .
  20. does anyone have a picture as I have never worked on one of these before ? thanks
  21. even in high gear when using the last to marks on the left lever I am only going 7 mph
  • Create New...