Jump to content


Photo

686-D-310 Injection pump diagram/parts(Leaking fuel from rear of pump)

Simple seal replacement?

This topic has been archived. This means that you cannot reply to this topic.
8 replies to this topic

#1 bredred

bredred

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts

Posted 30 May 2013 - 09:01 PM

Just bought a 686 with the 310 german in it that needs a few things. It has a fuel leak from the rear of the pump. Right in the center of the rear where the injector supply lines come out of there is  what appears to be a hex head bolt protruding from the pump. It is leaking from this bolt/seal/oring. What exactly is behind the bolt? Is there a seal or o-ring that I can replace? Don't want to start taking things apart without knowing what all's going on. If I have to remove the pump does it need to be timed before removing it? If so, where can I find a good writeup on removing the pump? I have an old cheap shop manual but it doesn't say a whole lot. Was hoping maybe I could fix the leak with the pump on the tractor and not have to take it to a pump shop and have it rebuilt. The tractor starts and runs great by the way. Thanks!


74' 966 IH M&W turbo; 67' 706 Farmall C-291; 80' 686 IH D-310; 03' C80 McCormick; 400 Farmall gas; 2- 140 IH's; 495 CaseIH; 885 CaseIH,
Past Tractors: 574 IH diesel


#2 Dirtboyz07

Dirtboyz07

    Advanced Member

  • Members
  • PipPipPip
  • 4,146 posts

Posted 31 May 2013 - 05:28 AM

Yes it can be replaced , Injecpumped ( Ed ) on here works at a fuel shop, I am sure he has the part or I can help you out too.

Danny
1984 Prototype 5388,1976 first built 1086 sn #8601 ,1971 1066 narrow front ,1984 3088 open station , Prototype 1206 sn#508, Super WD 9 Pro Farm pulling tractor , Steiger 9150 , IH 782 Cub Cadet , 1984 1420 combine , Load cell tractors from Hinsdale IH engineering TX148 sn 505 and 501 , experiential 884 XL mfd , experiential 784 mfd .

#3 Injpumped

Injpumped

    Advanced Member

  • Members
  • PipPipPip
  • 664 posts

Posted 31 May 2013 - 08:49 PM

Thanks Danny, I now actually own my own fuel pump shop now. I am thinking the VA pump just has a bleeder bolt in the center that seals on a taper, no seals or gasket. I could be remembering the wrong model VA though, been a while since I've worked on one.

#4 bredred

bredred

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts

Posted 31 May 2013 - 09:20 PM

Injpumped, so I probably need to just try tightening it up or putting some sort of sealant on it then? Thread tape isn't made for fuel....what about the liquid teflon sealant?


74' 966 IH M&W turbo; 67' 706 Farmall C-291; 80' 686 IH D-310; 03' C80 McCormick; 400 Farmall gas; 2- 140 IH's; 495 CaseIH; 885 CaseIH,
Past Tractors: 574 IH diesel


#5 Beans71086

Beans71086

    Advanced Member

  • Members
  • PipPipPip
  • 84 posts

Posted 31 May 2013 - 09:44 PM

Here is some fuel rated stuff if that'll help ya.

http://cleanfit.com/...ape_70885.shtml
NF 706 German, WF 706 German, IH 1066, David Brown 990, Oliver Super 88 dsl

#6 jm1456

jm1456

    Member

  • Members
  • PipPip
  • 20 posts

Posted 01 June 2013 - 04:44 AM

that bolt uses a soft steel seal,part number 3132407r1 about 5 dollars according to parts book it says o ring but is not had to do the same on my va pump



#7 Injpumped

Injpumped

    Advanced Member

  • Members
  • PipPipPip
  • 664 posts

Posted 01 June 2013 - 08:11 AM

JM, is right, there is a soft metal crush washer on some of those. You could try taking it out, look washer over good, and try reinstalling it if it looks ok. otherwise, it is an available item. That is simply a bleed screw back there, so nothing will fly out at you when you take it out. lol!



#8 bredred

bredred

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts

Posted 01 June 2013 - 09:16 PM

Thanks guys, I went and picked up the crush washer today along with some tie rod ends. Somebody had put a copper sealing washer on it instead of a crush washer so I guess that was the probem although I haven't put it back in yet. Thanks!


74' 966 IH M&W turbo; 67' 706 Farmall C-291; 80' 686 IH D-310; 03' C80 McCormick; 400 Farmall gas; 2- 140 IH's; 495 CaseIH; 885 CaseIH,
Past Tractors: 574 IH diesel


#9 Injpumped

Injpumped

    Advanced Member

  • Members
  • PipPipPip
  • 664 posts

Posted 02 June 2013 - 08:35 AM

thats good to see. The copper probably wont take injection pressure that that bolt is subjected to. VE pumps, similar to VA do use a copper washer, but it's counterbored for blowout protection. The right washer on there will seal it up. Great News!