Jump to content


Photo

TD7E Brake Job


27 replies to this topic

#1 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 07 February 2012 - 08:17 PM

I have the Tank pulled and the rear main cover cleaned off. Any helpful hints on doing a brake job (I know it can not be any think like my tuck :) )

TD7E - 4410020 U010270

#2 Zack

Zack

    Advanced Member

  • Members
  • PipPipPip
  • 85 posts

Posted 11 February 2012 - 02:38 PM

I would be interested as well, I need to start thinking about doing that this summer...

#3 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 08 March 2012 - 09:27 PM

Pad1.jpg I finialy got to the brake pads. When I got to the case the pad actualy came off the brake.
(see the picture)


Couple of questions:
1) What can I use to clean the case out with (some "stuff" has fallen inside the caseing) ?
2) I did not find all of the pad. Could this casue an issue ? where could it have gone ?
3) Where can I get a tranmission pump for my TD7E (serial number above) ?
I have a feeling that the pump is now shot. I will be taking it off this week end

#4 Zack

Zack

    Advanced Member

  • Members
  • PipPipPip
  • 85 posts

Posted 10 March 2012 - 10:49 PM

Here are a couple sites where you can get a new transmission pump:

http://www.brokentra...esser_trans.htm

http://www.highwayan...25000c91-360038

Any more pictures of the process?

#5 Iron&Dirt

Iron&Dirt

    Advanced Member

  • Members
  • PipPipPip
  • 85 posts
  • Gender:Male
  • Location:South Louisiana

Posted 11 March 2012 - 07:43 PM

Dont know if you have the strainer under your right but that is were your brake pads are. Might not need a pump. Newer models have the pads bolted on.

#6 Rawleigh99

Rawleigh99

    Advanced Member

  • Members
  • PipPipPip
  • 5,412 posts
  • Gender:Male
  • Location:Eastern Virginia

Posted 12 March 2012 - 10:03 AM

I find that a shopvac is great for getting out the small stuff that falls behind other parts. Stick a smaller hose that fits your needs into the big hose and used a wadded up rag wrapped around the end of the big hose as a "throttle" to control how much and when suction is applied to the smaller hose.
Rawleigh

1973 IH 500C a.k.a."Calico Cat"
1955 Cat D2 5U bulldozer with Hyster D2N winch
1945 Cat D2 3J crawler tractor
1979 Pettibone "Super 6" Forklift a.k.a. "Too Tall"
1973 Ford F600 Dump Truck
1980 Ford F350 Flatbed a.k.a. "Beastie"
1960 Allis Chalmers Model 72 All Crop combine
1966 Case 931 Comfort King Tractor

Sold:

1988 Mack R688ST Road Tractor
1955 IH TD 9 with Drott Loader

#7 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 12 March 2012 - 06:56 PM

Here is what I did (I may have to do this in several uploads)

Drained the Fuel tank, and marked the lines

Attached Thumbnails

  • Step 01.jpg


#8 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 12 March 2012 - 07:05 PM

These Lines are from under the Tank

Attached Thumbnails

  • Step 02.jpg


#9 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 12 March 2012 - 07:06 PM

Lift the Tank

Attached Thumbnails

  • Step 03.jpg


#10 DennisC

DennisC

    Advanced Member

  • Members
  • PipPipPip
  • 41 posts

Posted 12 March 2012 - 07:12 PM

These lines are from under the floor plates

Steering hoses (sorry not the official names). As you can see a bit dirty (and I did not have a pressure cleaner (yet)

Attached Thumbnails

  • Step 04.jpg
  • Step 05.jpg




Reply to this topic